- #Toshiba e studio 3555c firmware update update
- #Toshiba e studio 3555c firmware update Pc
MJ-1107/1108 (When MJ-6104 is installed) Transport path If there is any paper remaining on the transport path, remove the paper.
#Toshiba e studio 3555c firmware update Pc
(Hole punch control PC board (HP): CN3, CN5, CN6) Hole punch control PC board (HP) abnormality If the error still occurs after replacing the motor, sensor and connectors, exchange the hole punch control PC board (HP). If electricity is not conducted, replace the connector. Faulty cables and connectors Check if the electrical continuity between the connector terminals is normal. If the voltage does not fall within the range mentioned, replace the sensor. Then check that the measured voltage is 1V or lower when not shielded and within the range of 5V ± 5% when shielded. Punch sliding unit home position sensor (S23) abnormality Measure the voltage on TP26 on the hole punch control PC board (HP). If electricity is not conducted, replace the motor.
Remedy: MJ-1036 Punch unit sliding motor (M12) abnormality Check if the electrical continuity of the coil is normal. MJ-1107/1108 (When MJ-6104 is installed) Sideways adjustment motor (M2) Hole punch control PC board (HP) Description: Punch unit sliding motor (M12)abnormalitySideways adjustment motor (M2) abnormality: Sideways adjustment motor is not rotating or puncher is not shifting normally. Paper holder home position sensor Check if the connector (CN9) on the finisher controller PC board is disconnected from the paper holder home position sensor (S6) and the harnesses are open circuited. MJ-1108 Paper pusher cam Rotate the paper pusher cam. 
Paper holder home position sensor (S6) Check the connectors and harnesses between the paper holder home position sensor (S6) and the finisher control PC board (CN17).
Remedy: MJ-1107 Paper holder cam If there is mechanical problem when the paper holder cam is rotated, fix the mechanism. MJ-1108 Paper holder home position sensor Finisher control PC board Causes: MJ-1107 Paper holder home position sensor (S6) Finisher controller PC board. Description: Paper holder cam home position abnormality: The paper holder cam is not at the home position. Transport motor Check if the connector (CN10) on the finisher controller PC board is disconnected from the transport motor (M7) and the harnesses are open circuited. MJ-1108 Stack transport roller -1 Stack transport roller -2 Rotate the stack transport roller -1 and -2. Transport motor (M2) Check the connectors and harnesses between the transport motor (M2) and the finisher control PC board (CN5). Remedy: MJ-1107 Stack transport roller If there is mechanical problem when the stack transport roller -1 and -2 are rotated, fix the mechanism. MJ-1108 Transport motor Finisher control PC board Causes: MJ-1107 Transport motor (M2) Finisher controller PC board. Description: Transport motor abnormality: The transport motor is not rotating or the stack transport roller -1 and -2 is not rotating normally. Stack transport motor Check if the connector (CN17) on the finisher controller PC board is disconnected from the stack transport motor (M8) and the harnesses are open circuited. MJ-1108 Stack transport belt Move the stack transport belt. Stack transport motor (M5) Check the connectors and harnesses between the stack transport motor (M5) and the finisher control PC board (CN10). Remedy: MJ-1107 Stack transport belt If there is mechanical problem when the stack transport belt is moved, fix the mechanism. MJ-1108 Stack transport motor Finisher control PC board Causes: MJ-1107 Stack transport motor (M5) Finisher controller PC board. Description: Stack transport motor abnormality: The stack transport motor is not rotating or the stack transport belt is not moving normally. #Toshiba e studio 3555c firmware update update
Saddle control PC board (SDL) Update the firmware version of the saddle control PC board (SDL). Harness check Interface PC board (I/F) Board check Finisher control PC board (FIN) Board check Saddle control PC board (SDL) Board check Finisher control PC board (FIN) Update the firmware version of the finisher control PC board (FIN).Harness check Saddle control PC board (SDL).Harness check Finisher control PC board (FIN).Remedy: MJ-1108 Interface PC board (I/F).Causes: Interface PC board (I/F) Finisher control PC board (FIN) Saddle control PC board (SDL).Description: Saddle communication error.
Check if the conductor pattern on the saddle controller PC board (SDL) is open circuited or short circuited.Description: Saddle Stitch Finisher RAM abnormality.Remedy: MJ-1108 Reproducibility Turn the power OFF and then back ON.Description: Saddle Stitch Finisher flash ROM abnormality.
0 kommentar(er)
